Generally - tape the whole car off after stripping all the loose parts, primer, base coat (white), tape the whole car off again for the panda pattern, spray the black, remove secondary tape job, spray clear. Then the usual.wet sanding and buffing. If you're using spray paint you can just go to town...

you can purchase the parts at a dealer. Top & Bottom Insulators - 23291-75010 Upper O-Ring - 90301-17007 Lower O-Ring - 90301-14006 OR look for a set for the 1J injectors at the local parts store. Are you saying the 1J injector o rings are the same for the black top? Ahh those insulators I can ...

Just realised I hadn't replied to this thread, and that I probably gave some bad information :oops: https://i.imgur.com/Ugy1hDV.png On side feed injectors the two O-rings marked in red stop the fuel leaking top and bottom. The insulator marked in green looks to actually be a fat O-ring and it seals...

does anyone know how to do this?
Do you just paint over the fresh white paint..? or how do you prepare it..

Oops.... https://www.ebay.com/itm/Fuel-Injector-Nozzle-310cc-23250-16140-For-Toyota-Corolla-Camry-Turbo-Levin-4AGE-/302537622249 I think that pic you posted is incorrect. There is no need for an o-ring on the top as they are side feed injectors. And the ring at the bottom is actually the top seal f...

hello, this car is a swapped 4age and im not sure from what car but the gauges don't work...
The RPM and MPH works just not those 3 gauges
Gas
Temperature
Oil

What could the reasons be?

OK... we need to figure a way to get the fuel pump to run for a couple of seconds before you try and start the engine. If shorting the FP test plug didn't work ( and it should have) there is another way. You need to take the airfilter off your AFM (Air Flow Meter) and while the key is ON, push the ...

https://www.club4ag.com/forums/viewtopic.php?t=11360 If you can find the "T" shaped plug, use a short piece of wire or even a bare metal paperclip as a "jumper" to short or temporarily connect the two pins on the plug. Turn the key ON while the pins are connected and you should ...

totta crolla wrote:23260 on this diagram. http://auto-kat.com/index.php?route=sal ... group=2211

Disconnected it and it still started rough.
I put a paper clip into diagnostic port and it did not flash codes, the light was solid.

It sounds like it is over fuelling but I'm not sure that there is an error code for that when the engine is first started as the O2 sensor is not reporting. Have you checked for stored error codes? Maybe try disconnecting the cold start injector to see if there is a difference? I can check if there...

Cranking speed sounds about normal to me. If you were to turn the engine off straight after it started to run clean and smooth, and then start it again, would it still struggle and shake, or would it start up like normal ? I'm wondering if it is getting enough fuel for the first crank. If you have ...

Any chance you could post a video of the car starting up ? Right from the moment you switch the ignition ON and hit the starter would be great. Just a vid of the tacho with the sound of the engine so we can hear/see what you are hearing and seeing :) Cheers... jondee86 Hello! I have a video. https:...

Davegt27 wrote:Go for the easy fix first

Check grounds (that means clean grounds, take the ground wire and bend them back and forth to break up any internal corrosion)
Then reattach

which grounds are there that i can check..?

Cold start injector does not affect how fast the engine cranks. But if it is not working it will affect how long the engine has to crank at normal speed before it catches. If you have a timing light you could check the ignition timing while the engine is warmed up and idling. You should have around...

Sorry... got my posts mixed up :? Is the battery getting weak... cranks slow until it catches ? Easy way to check is to jump start your car using another car with a good battery as a booster. If the engine starts easily without struggling then your battery needs load testing to see if it is still u...

jondee86 wrote:Does it still blow a cloud of white smoke when you start it up in the morning ?

Cheers... jondee86

What do you mean blow a white cloud of smoke? like condensation?

I have a GTS 85 AE86, and whenever i start it, the car will crank a few times and struggle to start and will start but while it is cranking and starting the check engine light is flashing. After started, the car runs perfectly fine. What could be the issue? why does it have a hard time starting and ...

Might be cheaper to buy some of these and you will get the o-rings with the injectors. You will need to save the nose insulators from your existing injectors (rubber rings) that seal the tip of the injector to the inlet manifold. Refurbished items from China but don't let that put you off, they wil...

Might be worth checking if there is a business near you that can clean and flow test your injectors. Injectors don't usually crap out all at once, but they can get clogged up with dirt or old fuel if they have sat for a while. And if you are running a stock blacktop with a factory ECU, you don't wa...

Hello, I pulled out the fuel injectors the other day and want to replace them because i don't think they're working... I have two questions. 1) Do all new fuel injectors come with o rings or do i have to buy them separately? where do i buy them if so? 2) What injectors should i get? Would these work...

Doesn't sound like there is much wrong ? Was the engine still warming up when you made those clips ? Does it actually misfire when under load, as in while you are driving, accelerating etc ? Cheers... jondee86 Everybody I have talked to on Facebook Groups said it is misfiring. I mean it feels fine ...

https://streamable.com/a4fu6 https://streamable.com/tj6f4 Here are the two links of my car idling. I am not sure why it is doing that. I have changed the spark plugs and still nothing. The wires look brand new... My friend said maybe fuel injector? How do i check? And also, i heard people say to che...

Need this gone asap
Clean title in hand
Car starts
Have all interior and extra parts throwing in
Asking 2,000 OBO.

Lmk https://imgur.com/a/7rUlPK6

I use the same paint to do my interior plastics. What adhesive do you use to make the paint stick better? The paint scratches off easily without it. Bulldog Adhesion Promoter http://kleanstripauto.com/products/bulldog/bulldog-adhesion-promoter-aerosol My dash, door panel were perfect during my owne...

[quote="AE86Kai"]My old project http://www.club4ag.com/forums/viewtopic.php?f=28&t=16462 1) Clean the panel / plastic parts 2) Prep the panel (mask / apply adhesive promotor for extra sticky) 3) Paint with interior paint (ALWAYS paint the lighter color first -> then, darker color) For ...

Hey guys dropped in a 4Ac and have trouble with some wiring and grounds.. https://imgur.com/a/uNfembS Here is a link to all the photos. The car starts but idles at 4k RPM and there's spark near the alternator area... i see two grounds on the alternator but idk if its' suppose to be there Plugs near ...

Hello I gutted my whole car and wanna redo the interior... How do you guys suggest I paint the interior parts?
I am talking about
Door Panels the vinyls and the plastic interior parts... How do i start? Do i sand? I couldn't find a guide especially for vinyl door panels and plastic

The 'milky things' under oil cap was prob just condensation from moisture in the crankcase. Not uncommon to see in cool weather. (You also may see it in the valve cover breather.) When the engine reached temp it returned to the sump. Hmmm... So I dodged a bullet? Yes... tend to agree that you are o...

It sounds like you got water in the engine some way but it appears that you have dodge the bullet. I would just keep an eye on the oil and also the coolant level. Put a mark on the coolant over flow bottel at it's current level. This will make it easy to tell the level is changing. DaveW7 Should I ...

Responding to everyone here helping. Just drove my car and tried to go to 6k RPM and it felt fine. Barely any loss of power noticed. No overheat. I got out the car when i got home and there was no smoke. After like 3mins I checked the oil cap and i noticed this.. Is this normal? What should i do? ht...