Update list: 1) Randy 2) Nick 3) Tony 4) Ezekiel Fellas - I heard back from a supplier that the Toyota needle bearings are 1.5 mos delay from Toyota. I'm starting to get the other parts in but the needle bearings will have to wait and I don't feel like going non-Toyota parts for these. So unfortunat...

Update list:

1) s3cf
2) Randy
3) Nick
4) Tony

Autohaus_Z - are you one of the folks above?

Happy Monday everyone.

-Aaron

Hi here’s who I have. If you don’t want one let me know so I can move on. $470 shipped. ETA end of this week or early next.

1) s3cf
2) Sageren
3) Randy
4) Nick

Waitlist:
1) Tony

3 are spoken for. 1 still avail. Thanks. -Aaron

Exact same parts as pictured have been purchased and will be arriving from Japan end of next week. I’ve ordered enough for 4 total. However I’ve had to pay extra for a couple bearings so I’m increasing by $10 to $470 each shipped to US. Last time these sold in less than a day and one of the folks wh...

Hey thanks guys. Need to check with all 3 suppliers to see if I can piece it all together same as before and then obviously front the costs to secure them. I’ll repky back shortly. Thanks Aaron

Hi fellas,

May be able to get a handful more... I need to know who wants one... not simply interested.

Hi Jondee, randomly came across this and made me wonder... I know to put car in diagnostic mode when setting ignition timing and to set to 10 degrees TDC BUT what does diagnostic mode do specifically in terms of setting ignition timing? If we know it should be roughly 16-17 degrees not in diagnostic...

Thanks fellas and thanks Jondee so it seems straight onto the positive plug of the coil should do it. And correct that diagram you posted is the spal diagram provided.

Happy New Year everyone and long live the ae86! -Aaron

Hey fellas, installing a SPAL fan harness and it requires I splice into ignition so that the fan doesn’t run while engine’s off. Question: where is the best place to do so in the engine bay? I have the switch/harness positioned next to the coil pack but having problems locating the exact wire to tap...

Hey everyone, Selling a brand new custom Wilwood brake booster eliminator from Chase Bays (paid $199 plus tax and shipping) - see site to confirm. Never mocked up or installed - brand new. $150 shipped. Text me if interested 562-884-2094. Thanks -Aaron https://uniim1.shutterfly.com/ng/services/medi...

Replied. Happy New Year everyone!

UPDated - now 120 shipped!

Hey everyone, Selling a brand new custom Wilwood brake booster eliminator from Chase Bays (paid $199 plus tax and shipping) - see site to confirm. Never mocked up or installed - brand new. $150 shipped. Text me if interested 562-884-2094. Thanks -Aaron https://uniim1.shutterfly.com/ng/services/media...

Text me 5628842094 thanks -Aaron

BRAND NEW toyota AE82 water inlet pipe; if you're interested in going electric fan setup and need a place for the water temp sensor/switch (toyota part # 16321-15010. $30 shipped. -Aaron https://uniim1.shutterfly.com/ng/services/mediarender/THISLIFE/002092813322/media/33292932342/small/1504587895/en...

Cusco makes one for the hatch. Generally though it's not ideal since it's such a huge piece compared to the smaller coupe version. So chances of it getting lose from the rubber gasket and/or 'sagging inward' is def much greater. Not sure where you're located but as someone mentioned I went to a pick...

The one thing I would recommend is to replace the plastic bushing which goes on the passenger side of the aw11 rack. This minimizes the play between the rack and rack housing. Since you're already replacing inner tie rods and boot might as well do this vs finding out later you have a slight vibratio...

I spoke with Antonio from motormavens about this not too long ago and for that reason went with Tein camber plates instead as he said he's used them with stock hat and no problems.

I think Jondee nailed it. There's really no way you can shift without grinding unless the input shaft wasn't spinning, which would then mean the clutch disc is not fully engaged, which points to the release bearing constantly on the pressure plate. 2 questions - are you using the 'right' throw out b...

SOLD OUT (that was quick). Thanks Adam.

One more left....

Thanks, Alan!

-Aaron (text me @ 562-884-2094)

Just got 3 more kits in from Japan - I don't plan to order anymore - getting too difficult so plan on keeping one for myself! Exact same as above. $460 shipped. Alan - i just sent you a msg if still interested. Thanks everyone. https://uniim1.shutterfly.com/ng/services/mediarender/THISLIFE/002092813...

i do have an extra and have msg-ed you. thanks -aaron

Hey guys, I got 3 more kits coming in from japan - I plan to keep one for myself. FOBman & Jeonsah - as promised I'm giving you guys priority. Let me know if you're still interested otherwise I'll open it up for others. Thanks -Aaron

sent you a PM. sorry for the late reply - was out of town. -Aaron

Get the bride and be done with it - you're not going to find OEM that is in 'new' or 'like-new' condition and if they were they'd charge you the same

https://www.nengun.com/bride/floor-mats

What is the correct size/threading of the thermostatic switch that screws into the housing of the water outlet?

Drive shaft reduced by $50 to $225. You def wont see another one like this with a brand new carrier bearing...

GTS tranny sold