Like title says, I'm looking for the headlight arms that connect the headlight motor to the housing so the lights flip up and down.
Thanks

Thanks guys those 2 sensors i hadn't plugged in worked! it fired up within 3 cranks. lol i should've plugged them in the first place, i thought i could get it started for a while with out them and then worry about re-wiring later. good learning experience. thanks again for all the help jondee and jinx

I just realized that my ecu temp switch and cold start thermo switch are not connected because they used to be at the front of the radiator water neck near the thermostat. I had to put those switches in the back so now the connectors aren't long enough to reach the back. will reconnecting them have ...

that's the CAM timing u checked ? My GTS is hard as heck to start if I don't "pulse" the cold start injector (single one hi up on side of plenum). Use the same pigtail Mine fires right up after that. iirc the COR pulses it automatically on startup. Just not got to sorting my own yet yup, ...

Update..... I went to go chase down the wires in the loom for a short, started cutting the loom and tested for voltage on the yellow and green wire going to the ecu. I guess I must have shook something cause now I'm getting 12v to pins 10&20 at the ecu. I'm still not getting an injector pulse th...

cool thanks for all the info guys. i won't be able to test until next week but ill post back when i can. i did use my old injectors that were sitting for a while, figured i could still use them since i just had them cleaned before i removed the engine. ill try to energize the injectors and see if th...

r the injector contacts 'clean' ? one side is +ve 12V constant, while the ecu -grounds- the other termainal 12V to fire ez to set cam timing out 180º. Won't start contacts are good and I'm getting 3 ohms per injector. I'm only getting 12v on one side of the connector and the other pretty much nothi...

i have one that hasn't been used yet. just letting you know it hits the steering shaft. where are you located?

yeah i thought for sure that was my problem but they were bolted down.

Hey guys, So i have a rebuilt bluetop that i just dropped in, it cranks fine but i couldn't get it to start. Sometimes it sounds like its about to turn over but then it just keeps cranking. I have both spark and fuel. Fuel pressure is 35psi at the rail. I measured the voltage at the injector connect...

awesome work, much wow. Id say while you have the panels off, rust proof the insides. and use epoxy primer before you do body work. Keep up the good work!

I have zenki front and rear bumpers and they are starting to get dull. Right now they are looking like a faded gray color. Im wondering if anyone has painted they're bumpers, is it a good idea or should i just leave them alone? Im about to paint them black with a clear coat. Any pics of painted zenk...

alright cool...thanks for the response e80kind

jdm, zenki... or do i even need that support? not sure what its for

Anyone know the part number of this bracket in the picture? Its the upper support to the side of the front bumper. Not sure if both sides have this but i only have one on the drivers side.

Thanks

rxheaven1 wrote:Is this still available and will it fit the hatchback?

thanks,

It'll fit in a hatch but it will be just a little longer in the back so you would need to cut it a little.

My reverse lights dont work when in reverse. The lights work when i bypass the switch and the switch has continuity when i bench tested it. When i removed the switch it was filled with trans fluid. Is that normal or would that cause some problems? Thanks, any advise would really help me out

will you be getting more?

I love my corolla because I built it from the ground up. I know every inch of my car. I know exactly what bolts were replaced, needs to get replaced and the places it needs bolts =) If that makes any sense. I love the smell of the oil burning, coolant leaking, tire burning, side mirror shaking, tie...

I might be purchasing a set of t3 pulleys. Does anyone have any pics of them installed?

i got one, you can have it...just pay for shipping. it'll come from hawaii though. lmk

bump

so can i still use the ac lines and ducts from the 4ac or would it be better if i just find a full set for 4ag?

Illegal_Garage wrote:I have 4 of the left side

LMK if interested

Max

how much for 1, i need it shipped to 96766? you think youd be able to find the right side anytime soon?

shoots, thats what i figured. Thanks for the help!

So i have a 16v 4age motor, im can get a 4ac motor with a/c equipped. My question is will i be able to bolt the a/c up or will i need to do some modifications? im also going to switch to manual rack so i think im gonna need a different type of ac bracket? Thanks for any help

bump

bump

bump

bump