[QUOTE=oldeskewltoy;1110545] along with assembled short block - those are Molnar Tech 40/20 H- beam rods http://ost.ebeans.ch/albums/userpics/10005/block_top_and_bottom.jpg More to come..... :D[/QUOTE] Did(Do) you see it???? How about if I point it out....... http://ost.ebeans.ch/albums/userpics/100...

everything is back in my hands for final assembly.... head, with fresh valve job (machined .008")... http://ost.ebeans.ch/albums/userpics/10005/ready_for_re-assembly~2.jpg along with assembled short block - those are Molnar Tech 40/20 H- beam rods http://ost.ebeans.ch/albums/userpics/10005/bloc...

On a related note. For "3rd party" cast pistons, which don't already have a coating (whatever it is that was done on OEM 10.3:1 pistons), would having the domes ceramic coated help when pushing for higher-than-stock HP? I'm guessing it at least helps with heat dispersion and so prevents h...

There isn't a horsepower limit... there is a tuning limit. There is a "flaw" with all the n/a pistons for the 4AGE... the 2nd compression ring rests on ring land that is not well supported (piston on right in photo) http://ost.ebeans.ch/albums/userpics/10005/ring_land_support_slot_vs_holes...

and the internals.......





crank on right has wankered key groove in snout




more to come.....

https://media.giphy.com/media/3htAT2no2D2ukVsUE2/giphy.gif centerlines are now known... and my guess was wrong........   I had thought they were 116+ do to the smooth idle, and the short powerband...  I was wrong!   The cam has a 110 degree centerline....  no need to screw with moving it!   So, the...

I guess that was my question. Will there be any potential engine damage for driving around with a vehicle that is not properly tuned (not for very long), but am assuming at least 100-200 miles before the ITB kit and the standalone ECU is installed. being 100% honest... I don't know...odds are there...

Can the stock JDM 16v ECU run the car ok ? "Ok" - a lot would depend on what ok actually means... but it should run on stock JDM management, how well is another story... The stock computer uses a whole bunch of different parameters(stock engine), you have changed many of those... so, it s...

Getting the flowbench prepped for the 5V-EU head..... .... and getting the 5V-EU head ready for the flowbench.. more to come..... :D I spent a while looking, but never found anyone who had flowed a 5V head before... so I did. http://ost.ebeans.ch/albums/userpics/10005/flow_test~0.jpg That is pretty...

look in your own area for powder coating, and show them the photos.

a few pointers... Dont get them coated on the inside, and make sure breather is taped closed during coating

Drum roll please...........





more to come....

Well, the new valve tool is ready..... I'm only using test springs in there, so it doesn't have to be too stout. http://ost.ebeans.ch/albums/userpics/10005/fabbing_flowbench_valve_actuator_tool_rotated_4_panel_smaller.jpg now I just need the time to finish the set up, and calibrate the bench(new se...

Breath taken sir. So question for you then, to simplify everything. What do you think about this option: Red top pistons MRP stainless steel valves - https://www.mrpltd.co.nz/product/4age-16v-stainless-steel-valves-0-5mm/ Stem seals MRP connecting rods - https://www.mrpltd.co.nz/product/4age-billet...

one quick note... When talking about cams you will see me put a number in quotes, followed by "type", as in "264" type . Not all cams are equal. because of this I tend to look at a cams duration numbers based on what duration they are at either .040"(1mm), or .050" lif...

one quick note... When talking about cams you will see me put a number in quotes, followed by "type", as in "264" type . Not all cams are equal. because of this I tend to look at a cams duration numbers based on what duration they are at either .040"(1mm), or .050" lift...

I probably put more things for generic engine rebuild stuff on things that I decided to not go with. Do you have any recommendations? Here is my compiled list so far... Pistons: ⋅  4AG Red Top High Compression Pistons, 10.3:1 : $530NZD -> $342 USD ⋅  Brian Crower 12.0:1 Pistors ...

Sorry this is my first appearance... I typically avoid ITB threads... they aren't often needed(my 140+ whp smallport runs just fine on a single T/B), and if not done correctly can and often does cause operational issues do to poor set-up (mechanical, as well as from a management POV) I am absolutely...

oldeskewltoy wrote:

4 down....




more to come.....

what does "tumbling" the head consist of? Is it similar to tumbling bullet casings? Not sure (tumbling bullet casings...???) What "tumbling" means in this case is they have a large tool - it consists of a large cabinet, with a rotisserie that you strap the head too. The cabinet ...

http://ost.ebeans.ch/albums/userpics/10005/one_done_2_not_yet_begun_edited.jpg more to come.... :D http://ost.ebeans.ch/albums/userpics/10005/2__annoted_for_2_panel.jpg http://ost.ebeans.ch/albums/userpics/10005/2_done2C_3_not_yet_begun.jpg http://ost.ebeans.ch/albums/userpics/10005/bowls_2_and_3_c...

Work begins.... One done... http://ost.ebeans.ch/albums/userpics/10005/intake_side_one_down.jpg http://ost.ebeans.ch/albums/userpics/10005/exhaust_side_one_down.jpg http://ost.ebeans.ch/albums/userpics/10005/one_done_2_not_yet_begun_complete.jpg and a bit closer... http://ost.ebeans.ch/albums/userpi...

OST-064 "Cleaned".... http://ost.ebeans.ch/albums/userpics/10005/partially_cleaned_ready_for_port_work.jpg After getting it cleaned, I deburred the casting http://ost.ebeans.ch/albums/userpics/10005/deburr.gif And then before porting, I had it "tumbled" so the head now looks new,...

Have a bare small port block with squirrels for sale. In good shape. Also have small port pistons and rods if needed. Located in Oxnard CA Block: $60 Pistons and rods: $120 any chance you can get it to Portland? Looked into it, fedex would be cheapest option but still pretty expensive at about $150...

more to come.....

2nd cheap 7 rib block... but neither close enough..... to Portland

Eddiegonz__ wrote:Have a bare small port block with squirrels for sale. In good shape. Also have small port pistons and rods if needed. Located in Oxnard CA

Block: $60
Pistons and rods: $120

any chance you can get it to Portland?

It's time to move on.... (was $22,500 USD, now asking $19,900) Instead of me re-creating this, I thought I'd just copy/paste the ad that I read when I bought it...... albeit with 2 new pieces of info 1) the car with some fuel(about 5 gals) weighs 2021 pounds. 2) the cross weight on this car with a 2...

Does anyone really need a 300mph 1000hp sportscar ? Youtube is loaded with videos demonstrating that such vehicles are not a good match with the driving skills of the people who can actually afford them. So I don't think that the drivers of lifted trucks are the only ones compensating for their sho...

Driverone wrote:I figured out that i cant pm you because im not to active here sry. Probably both.

send me an email oldeskewltoy @ yahoo

I keep pluggen' away........