E_Money wrote:I want to know what everyone thinks or considers a "fanboy" when it comes to AE86.

an AE86

268 is a bit lopey for a stock engine.... it will likely lower dynamic compression as well... if you do nothing to bump static compression.

Orange Rocket is selling a brand new pair of Crower cams for $450... that is pretty cheap.... albeit they are more duration.

Where can I find all these parts? Im unsure of what engine I have and how many ribs. Sorry Im new to the toyota world and absolutly clueless. 7 rib block... and why you prefer one.... top photos show 7 rib block stiffening over earlier 3 rib block(upside down photos) http://i79.photobucket.com/albu...

ANY time a different cam is installed you should check clearances.

Hi I bought a 1986 toyota corolla GT-S. It came with power windows and power sunroof but no power steering. Also is black an original color for these cars? I saw on my fuel cap door a few red paint showing after paint chips. The engine bay is black. I wonder if the previous owners bought a replacem...

http://i79.photobucket.com/albums/j143/oldeskewltoy/ae71/fromto.jpg engine compartment before... http://i79.photobucket.com/albums/j143/oldeskewltoy/ae71/PICT0021.jpg After http://i79.photobucket.com/albums/j143/oldeskewltoy/ae71/PSIdynopic1.jpg Transmission Before... 5 speed(on left), after... 6 s...

Get a little E7 love in :mrgreen: mine... http://i79.photobucket.com/albums/j143/oldeskewltoy/ae71/dansCorolla5.jpg a pair that were my inspiration... 1... http://i79.photobucket.com/albums/j143/oldeskewltoy/ae71/whitehardtopIlikesmall.jpg and 2 http://i79.photobucket.com/albums/j143/oldeskewltoy/ae...

A well built 16V with decent headwork can make VERY good power....... To keep it all simple..... run factory ecu and wiring..... 7 rib block(with proper attention to deck height), 3 rib crank and rods. Have the rods modified to accept the larger 20mm pins - press fit. Have the crank and rods prepped...

Tony.... do some research into "pressure recovery". The silvertop combustion chamber (or a welded, and ported blacktop chamber) is more conducive to "pressure recovery" then an unmodified blacktop chamber...... http://sphotos-b.xx.fbcdn.net/hphotos-ash3/544680_390016947708044_113...

In For Sale section there is....

AE86
4AGE
FT86
I6, V8, big sedan


What no love for E10-E70? What about fwd... other E80s, and E90 on? No love for K power or T power or S power?

You didn't break another T50 did you? http://i79.photobucket.com/albums/j143/oldeskewltoy/LEEN/destroyedT50gears_zpsc7c83fcf.jpg One of the most common short comings with the AE86... and in fact ANY rear wheel drive car utilizing any of Toyota's "A" engine series... is the original T50 - t...

griplimited wrote:- The car used started as a $400k DB6 and went through restoration to look the way it did today.

I had a chance @ a Superleggera DB5 back when I was 20.... they only wanted $3500.00

Tony... Do I spy my logo??? LEEN informed they would be putting my logo into the 2nd generation...

would love a side shot showing it

One additional question, I was reading up on the piston differences and it seems these 8.9:1 GZE pistons are forged instead of cast. Does this mean the block bores should have some extra clearance to allow for piston expansion? Or don't I have to worry about this? I can only hope that I will find a...

http://img.photobucket.com/albums/v375/garbageboxlove/car_88-toyota_all-trac/4a-ge_build/4a-gze_8-9_1_piston_w_wrist-pin_zps3988fa61.jpg Those pink rings are pin locks, or keepers... they snap into the pistons and restrict the pin from moving beyond the clip. In 18mm applications there is no such c...

Moto....

I tried to have multiple windows open @ the same time(4?) and my RAM hit a wall (I've got 1 Gig of RAM)... is there any way to reduce the adverts??

LEGIT! When ever you are ready Ronny... ;) I'll be happy to massage a cylinder head for you..... :twisted: Here are a few of my previous builds - https://www.google.com/search?q=oldeskewltoy+ost-+%22hachiroku.net%22&ie=utf-8&oe=utf-8&aq=t&rls=org.mozilla:en-US:official&client=fi...

dr.occa wrote:20mm wrist pins must be pressed in.

This is incorrect... ALL of the 4AG stuff using 20mm wrist pins should be full floating.

sometimes the fit is VERY tight...

A quality port job can add power,and ECONOMY, even while retaining stock parts! Because casting imperfections are removed, not only are power gains likely, but more even airflow promotes even combustion, which promotes cleaner emissions. More airflow, more power... less throttle angle required to ho...

also agree with getting your injectors cleaned... I've had good success with RC Engineering - http://www.rceng.com/Fuel-Injector-Cleaning-P43C0.aspx

didn't take long for the spammers to find......

Wow... I had to re-register........ I guess I"m a newbie