Cheap method is to elongate the knock pin hole. Done it. It works. But it's no where as good as a set of adjustable gears. Another way that is cheap is to drill indexed holes like the old TRD method. Indexing the holes requires a fair amount of attention and at least a degree wheel. The slotted pin ...

Add parts

Won't be able to text until I go into town, no service at home. But the block is still available and located in the SLO area.

Mustang? Mustang? Uh, you mean Muskrat??

I have those pieces. Check your messages, or e-mail me at walinggamit@yahoo.com

Yep, been there done that. Even tried using FIPG, but I haven't found anything to really do a good job. I did get lucky enough to find a good tube at the wrecking yard.

Is the intake piping actually cracked? If you need to replace it a simple and cheap method is with a couple of silicone couplings and aluminum piping. My example; http://i895.photobucket.com/albums/ac155/walinggamit/034_zps364fed60.jpg I used a 2 3/4" mandrel bend 45 and cut to fit. Couplings a...

You can cut the top off the rear strut body and weld a screwed top on from a donor strut. I did this with one of my FX16s. I used the body from an AW11 MR2 front strut for the rear struts. Make it work! Modify and adapt. Or just get a set of purpose built parts. Lots of coilover sets available out t...

Have you thought about going with Ground Control or full coilovers?

Suspension upgrades? I have BC coilovers and Whiteline sway bars and complete bushings set. I like the way it handles this way! All those parts are a bit pricey, but well worth it! I'm in CA, so the engine mods are limited. A set of mild cams and raising the compression to a level that your area's f...

MR2 trans is one part that won't interchange, sorry, the shift lever is on the wrong side. Any FWD trans that bolts to an A series will work. As for the time involved? Take your time and be thorough and an afternoon should do it. As for the GZE, Look around for any writeup on that. I read one and I ...

I've had a few of these, currently an '87 GTS. I don't have a manual, but I found it easy to do the clutch by dropping the trans out the bottom. I borrowed a nice tool from a friend that supports the engine from above using the fender rails. You could use an engine hoist or floorjack to support the ...

The manifold in the pic with the gasket is an intake for a GZ. I had an AE86 before and never found a header with an EO. So you are pretty well stuck with looking for a stock exhaust manifold. The manifold from a FWD won't fit, so make sure it's for a RWD. Good luck.

I haven't found any "chips" for the USDM 4AGE models. The piggyback units won't work either, so don't waste your time and money on them. If you don't plan on doing a lot of work and keep the FX pretty much stock look into intake and exhaust mods they're the easiest things to do. Maybe play...

Sent a PM. I'll be going through Lemoore either Saturday or Sunday, probably Sunday.

I have plenty of those.

I could meet, I go between Fresno and SLO. Where are you located?

Adding a fuel rail to the list. Supercharged small port fuel rail, with the pulse damper on the end instead of on top, $40 + shipping.

If by top half of air box you mean the box over the throttle bodies, I have that available.

Still have these

Adding a couple of parts. Set of JDM coils and bracket with Nology wires. Also have a BOV in good condition.Selling the last of my SC bits. A JDM SC12 and 175mm pulley. Pulley is aluminum. SC12 is in good condition, rotor coating is still intact. Pulley $150 and the SC12 is $250, shipping is additio...

I just have the distributor and harness.

Price would be 110 + shipping

I've seen the 2ZZ in mk1 MR2s, so the AE92 should be possible. The exhaust exits the opposite side of the engine so you'll need some heat shields on the firewall. The trans on the 2ZZ is the C series, so it might bolt to the stock crossmember. Axles may give you a bit of a headache. I think the S/C ...

Shipping alone would be 80 bucks.

What town are you located in?

Sorry, can't text from home, it's a dead zone for my cell. My e-mail is walinggamit@yahoo.com though if you could go that way.

I have one here $65 shipped U.S.. You'll get the IAC and the throttle body as a unit.

I have an AE92 MAP harness I'm not going to use, it has the proper distributor with it. This harness is for the grey 26-16-12 pin non T-vis ECU. Sell for $125 shipped. If I find an ECU for this harness I'll pull the offer off the table.

Selling a set of electric mirrors off an '89 AE92. They're in good condition, I just won't be needing them. $125 shipped CONUS.