ebay my friend

http://www.ebay.com/sch/i.html?_sacat=0&_nkw=toyota+4+runner+radio&_frs=1

if you are asking if the levin front will bolt to the trueno rad support the answer is yes. im not sure if they are the same tho

I have a set of Brand new wheel caps. one has been opened to test fit on my work wheels but since my wheels are the old 80s style 1 piece they dont fit. I would like to trade these caps for a set of center line pop in caps in good to new condition or a set of the older style work equip caps. let me ...

I would think some large washers would help as well to prevent the bolts from being pulled through the sheet metal.

if your cel is staying on then pull the codes your self. that will give you a general starting point at least. also try ti repair the original harness to save those dollars 2 grand is not worth it you can get your harness completely repaired for about 500 bux from a good professional

I have a 200mm 8 bolt flywheel and clutch from a ae92 for 50 + shipping. yes the mr2 will also.

I have a 7 rib block rods and pistons but no crank if your interested. i can throw in a crank but i dont think it is usable but your machinist might have a different opinion then mine does. i will sell them for 125 + shipping.

get one from a civic. its not exactly the same but it is a lot easier to find and it works. iv used one when my tvis plate was removed.

bump make a reasonable offers and will accept trades for a 42mm crank and 20v exhaust cams maybe other parts so just make offers thanks

I have an exhaust cam and gear from a B/T. I also have a 42mm crank, still in the block. Journals are standard and the crank is straight. what price are you looking for for both shipped to 77584? also are all the rod and main journals good? will i have to do any machining to the crank? and what eng...

Ill take 36, 58, 100, 84, 57, 85

SidekickChuck wrote: I have a 10 inch rear wheel (0 offset with a moderate 1 inch spacer) with 225's and there is still some room left inside the fender.

this is the same thingas 15x8 -25 and the car pictured has fender flares???

^^lol you can maybe find a local fiber glass shop to make a single exhaust rear valence or some sort of cap that will cover the other side. Maybe get your local body shop to work some auto body magic and cut and patch it to remove it. why not get creative and get a single round fog light and hook it...

I am testing the waters to see what is available. I will need shipping as i am in TX. I am mostly looking for a Black top crank in good usable condition but i will consider any 42mm crank. let me know what you have with a shipping price and detailed pics of all main and rod journals. I would also fe...

I dont think the 15x8 +25 will clear the front strut casings. i could be wrong but that is a whole inch closer then the 0 offset and the 15x8 0 offset is pretty close to the strut casing as it is. -25 offset and you will be closer to the fender but i dont think you will get 205's on the -25 offset u...

flywheels really dont do anything for acceleration it will do more for throttle responce tho. your engine will rev a bit quicker but like stated above when you are in gear driving down the road you probably wont notice a whole lot. if you are all ready in there then go for it it deffinately wont hurt

I have one ill sell for 25 + shipping. LMK send me a pm and ill respond faster thanks

according to fedex it will be about 150 to 175 sent by fed ex ground. i can check other shipping places like ups and usps but i dont think usps will ship it due to the weight.

I have a used clutch and flywheel that is in good shape the clutch disk is 7.6mm thick and i have a t50 shifter. ill throw in the shift knob for free I also have a large port oil pan and windage tray. oil cooler hose fitting is still there too with drain plug. LMK

I have a 200mm clutch with pressure plate that has 7.6mm of meat left. well with in spec ill sell it for 30 + shipping LMK. I have a 200mm 8 hole flywheel also if you need it

bump

bump

I would say the center bearing are worn. i had the same issue on my drive shaft. if you look on amazon you can find a chinese center bearing for about 15 bux or so. if you want the oem bearing then expect to pay about 80 bux to 120. it does sound like with all the play that your center bearing is ba...

I prefer 14 over 15 14 are usually lighter then most 15 in general but not always. also with 14 you can run a shorter tire and still have a decent side wall. I run a 14x8 with a 185/55-14 tire. not only do i still have a 55 seriese side wall but it also changes the final drive ratio to about 4.5:1 r...

I think you can use the large port afm as long as it comes from the 88 - 89 corolla gts. according to toyodiy it says they use the same afm. as for the large port from the ae86 im not sure about how it will work with the small port ecu :/ about using the 4af block, it will work. you should check the...

free bump for peter he is a great seller

bump

where you bought these header they should give you a part list of whats included. what kind of headers are these? i got it from someone but there were no studs with it I have some used 4age OEM studs with nuts if you want. let me know how many you need and ill see how many i have. if anything i kno...

I would say get all your parts from an 88 - 89 corolla gts and i am willing to bet it will just fall together like it was actually a corolla.

I have for sale 4age 7 rib block from a 88 corolla gts large port $75 + shipping 4 42mm/20mm pistons and rods 9.4:1 comp ratio also from a 88 gts corolla large port for $50 + shipping 200mm 8 bolt flywheel and used clutch for sale $50 + shipping. next is a zenki welded diff. no r&p no pumkin. ba...