The first part of the story.
viewtopic.php?f=4&t=3564&p=96244#p96244

my instagram "japanese.shop"

All work done with his father dvoem
Now raskaz about what has been done for 4 years.



bought the clutch basket and clutch release "exedy" on MT T50.


was bought by motor 4a-ge.


Made kontovatel to rotate the car.


engine installation


it took about half a year, cars stood almost untouched. Cooked inside of the rear wings

made sand blasting equipment

in 2012 there was a strong degree
Video
http://www.youtube.com/watch?v=bphq-WgsSEw
http://www.youtube.com/watch?v=KOhCF9TtolE
continuation will write later

Первая часть рассказа.
Всю работу делали двоем с отцом
А теперь расказ о том, что сделано за 4 года.
мой инстаграм
работали только с отцом


куплено сцепление, и выжимная корзина "экседи" на МКПП T50.
был куплен мотор 4a-ge.
Изготовлен контователь, для вращения автомобиля.
установка двигателя
прошло около полу года, авто стояло почти не тронутым. Сварили внутренние части задних крыльев
сделал пескоструй технику
в 2012 году был сильный град
продолжение напишу позже

Was mauled threshold




cut out


made a new threshold


the rigidity of the body


drilled

straightened and secured by welding


Ve rests on the body with rust, of course he's not rotten, but to cover all anti corrosion, so after half a year rust went on. I didn't dare. continued
the search of the compressor.

working in a garage if possible.
try to do everything efficiently for yourself why so debt

Subscribe ! my instagram "japanese.shop"

был повтор

made sandblasting







To be honest it is very difficult in this busy
to say dusty job , then there is nothing to say=)

Subscribe ! my instagram "japanese.shop"

сделал пескоструйную обработку

Скажу честно очень трудно таким делом заниматься
сказать пыльная работка , то есть нечего не сказать=)

Wiring
ae111
Purchased automotive wiring
the engine compartment. salon





Куплена автомобильная проводка
подкапотная. салонная

ПОЛИУРЕТАН

INSTALL RADIATOR

well, this is how it sits now



After treatment by sand blasting the bottom from corrosion.
the bottom of the car looked like this here




then came the long-awaited moment when we covered the bottom with soil.
the Epoxy primer.











УСТАНОВКА РАДИАТОРА

ну и вот так вот он сейчас сидит

После обработки пескоструйкой дна от коррозии.
дно автомобиля выглядело вот так вот

настал тот долгожданный момент когда мы накрыли дно грунтом.
грунт Эпоксидный.

Several layers of the soil

salon




protection

to lubricate the joints in the hind wings sealant
it was so




It happened




Coated with anti-stone chip






It's already on another day


the seams in the cabin


frame for optics

struck a white ground


[img]https://c-a.d-cd.net/1042ea4s-960.jpg
[/img]


Несколько слоев грунта
салон

промазать швы в задних крыльях герметиком
было так
так стало
Покрыл антигравием
Это уже на другой день
швы в салоне

рамки для оптики
нанесли белы грунт

3 years have passed
video
https://youtu.be/uKUnAZp0aUg

удалил повтор

epoxy primer,acrylic primer
























primer body
first gray epoxy primer
then the usual white.

videos dyeing machine
https://youtu.be/Wn2pnbNVazc
instagram "japanese.shop"

the manufacture of the exhaust manifold
so it looks factory, under the front-wheel drive

Sketch

this is what happens=)

the real difficult task to do the exhaust manifold. someone experienced who knows=)

polyurethane



the fuel pump. 2jz-gte

The gas tank. carburetor

on a lathe. did flange

under the puck from supriya

Hole sawed electric jig saw


welded to the tank thread

we filled up the water. Check for leaks.

fuel line supra jza80

installation of the bridge



exhaust manifold

the exhaust manifold.The final stage



spider 4.1
layout




did flange

[img]https://c-a.d-cd.net/f5f6d5cs-960.jpg
[/img]

you like? what we have done?
hung the exhaust pipe

under the exhaust was done about 6 mounts



wrapped the entire exhaust manifold thermo tape








do you like it? what we have done?

salon carpet washed

scattered wiring in the garage from ae111 Levin



pasted interior sound insulation, rigid in two layers, gone 3-4 days



automotive wiring ae111

Cool light wheels Old School
Bridgestone ZANA SPOKE 6 MADE IN JAPAN



5 kg

it is time to bring them in proper form



well I washed them. about 30-60 minutes on each disk


Soaps with various detergents,they were very greasy

Then started polishing shelves
time about 4 hours on each disc
3 days is gone.
and the finish polishing for 30 minutes on the disc


prepared disks:
degreased, Packed in polyethylene.


and away we go



3 layers of gold and 4 coats of varnish

the camera does not convey the beauty=( from different angles in different color,



beautiful





do you like it? what we have done?
You interested?
Should I continue?

Excellent work! Definitely keep us updated!

Wow that's a lot of work. Keep it up and show us the finished result!

Great work, keep it up! crazy russians! :]

Good time dear readers.
We started the car.
here are two videos.
https://youtu.be/Tg5YC8Xt780
https://youtu.be/g7yYHKsUCoM
sorry that the forum is not to post the video so

I will try to describe as much as possible just what is done.

here are the seats, they were on the roof of the shed 4 years=)

the interior was completely washed: carpet, trim, foam seats

Two sides of the driver's seat was worn out, I had to replace them

More or less reschedules with wires


this chip switches

set the stove

washed the motor janitors
https://c-a.d-cd.net/e82ca02s-960.jpg
started splicing wires. aa60-ae111

It's a difficult thing. I have no specialty electrics. but we did,carefully. and as needed.
Replaced the cord on the gas pedal, as the old one was short
on 14 February a Russian holiday. St. Valentine's day.
This day I spent in the garage. till about 2 am.





.
The salon after washing and sewing.
https://e-a.d-cd.net/b98ca02s-960.jpg
The salon is almost assembled.

Brake lights, restoration

the car was purchased without stop signals.
Long sought brake lights, at that time in Russia I have not found, in Japan at the auction was not.
Somehow turned up option't remember exactly Ukraine or Belarus.
auto sawed in pieces and sold.
one stop signal was not glued, and the glass slides were on a delay=)
+ two stop signals were very dirty, about 3 hours I washed them
Since the optics was not new. there were chips, scratches, and cracks.
It was decided to revive them.
https://h-a.d-cd.net/3eede02s-960.jpg


Polishing


the initial state of the stop signal

https://f-a.d-cd.net/c3ede02s-960.jpg
polishing

Rama, on the stop signal

now do the same with the second
https://f-a.d-cd.net/3dde02s-960.jpg
https://f-a.d-cd.net/f01de02s-960.jpg








I think it turned out well

Very nice!
You did good work making it look good again

RuizXIII wrote:Very nice!
You did good work making it look good again

Many thanks that you estimated our work =)

Today there will be a post. This work literally the other day is finished.
Остлось slightly =)
Hello dear readers. one more board the magazine devoted to assembly of the car.
As the old cable of gas was short, other rope of gas is established.

Door glass, and moldings was bought

Here and so moldings looked
https://a-a.d-cd.net/91ecc42s-960.jpg
https://g-a.d-cd.net/71ecc42s-960.jpg
polishing


About the beginning looked so





- I established stoplights.

https://f-a.d-cd.net/291cc42s-960.jpg

established an oven faucet

Fastenings under conducting are made. established conducting that passes in front

established an oven faucet


as the radiator not native, and is one many more, from motor ge
fastenings of a radiator in the heel remade.
this time made fastenings of a radiator in the top part


Made fastenings and fixed the block of safety locks that under a cowl.

that's all =)