Dash refurb: what fabric?
Dash refurb: what fabric?
Today I pulled my cracked dash out and set about stripping it down. The foam pad removal was fairly easy; I used a flat head screwdriver and chipped off all the foam and brittle old vinyl cover pretty easy. Then what was leftover I soaked with some acetone and sanded off. Now I have a smooth plastic shell of a dash.
I want to recover the whole dash with one piece of fabric with a little foam padding underneath; like the factory dash. I want to cover over the clock and all the vent holes. With the foam removed, there is a small lip around each hole so I can epoxy a flat cut-to-fit plastic cover and fill in the edges smooth.
My question is: what fabric should I use? It needs to be stretchy so it goes over those sharp angles around the gauge cluster. It must have a matte finish so it doesn't cause any glare. It doesn't necessarily have to be black, as I am also stripping the interior to paint it a gloss silver. (white is too hard to keep clean [see my engine block!] and black is too gloomy)
I want to recover the whole dash with one piece of fabric with a little foam padding underneath; like the factory dash. I want to cover over the clock and all the vent holes. With the foam removed, there is a small lip around each hole so I can epoxy a flat cut-to-fit plastic cover and fill in the edges smooth.
My question is: what fabric should I use? It needs to be stretchy so it goes over those sharp angles around the gauge cluster. It must have a matte finish so it doesn't cause any glare. It doesn't necessarily have to be black, as I am also stripping the interior to paint it a gloss silver. (white is too hard to keep clean [see my engine block!] and black is too gloomy)
Eric'sFreeAE86 from the old site
Knockoff Crew member #0001
Knockoff Crew member #0001
-
- Club4AG Expert
- Posts: 418
- Joined: Wed Jan 09, 2013 9:16 pm
Re: Dash refurb: what fabric?
What about DiNoc dry CF or matte finishes? Or are you opposed to vinyl covering?
Silver/Black 1985 ae86 gts Heavens Gate Corolla
2001 Carbon Black e39 M5
89' Supra Twin Turbo 1JZ (sold)
2001 Carbon Black e39 M5
89' Supra Twin Turbo 1JZ (sold)
Re: Dash refurb: what fabric?
I hadn't considered that yet. Would it stretch enough?
Eric'sFreeAE86 from the old site
Knockoff Crew member #0001
Knockoff Crew member #0001
-
- Club4AG Expert
- Posts: 307
- Joined: Sat Jan 12, 2013 10:28 am
Re: Dash refurb: what fabric?
Use a hair/blow dryer and it will be plenty stretchy, not sure about the carbon style wrap, but the matte stretches and covers nice. Its quite a bit of work though and help is nice to have.
Re: Dash refurb: what fabric?
Oh what about headliner material? It already has a foam padding back and it's stretchy
Eric'sFreeAE86 from the old site
Knockoff Crew member #0001
Knockoff Crew member #0001
Re: Dash refurb: what fabric?
Ok so now I'm looking at this flocking kit I've seen on a couple other forums; but with varying results. I found a Subaru WRX that looks ok, a GC8 that was over done, and an Evo X that looked like butt in the pics. Everyone responding is all drooling over these kits, but I'm not super impressed. Plus it looks like a messy job; spray the adhesive then spread on the fibers and let it cure. Straight forward sure, but messy I think.
I found a Korean company that sells a self-adhesive spandex-based faux-suede that I think will look nice, and it should be quick and easy to use. Today I have to cut up some plastic storage tubs for panels to cover the clock and vent openings and epoxy em down.
I found a Korean company that sells a self-adhesive spandex-based faux-suede that I think will look nice, and it should be quick and easy to use. Today I have to cut up some plastic storage tubs for panels to cover the clock and vent openings and epoxy em down.
Eric'sFreeAE86 from the old site
Knockoff Crew member #0001
Knockoff Crew member #0001
-
- Club4AG Pro
- Posts: 582
- Joined: Wed Jan 09, 2013 6:10 pm
Re: Dash refurb: what fabric?
carbd7age wrote:Ok so now I'm looking at this flocking kit I've seen on a couple other forums; but with varying results. I found a Subaru WRX that looks ok, a GC8 that was over done, and an Evo X that looked like butt in the pics. Everyone responding is all drooling over these kits, but I'm not super impressed. Plus it looks like a messy job; spray the adhesive then spread on the fibers and let it cure. Straight forward sure, but messy I think.
Came here to mention the Flocking. Looks awesome, probably a huge mess to DIY.
Im leaning to this or just wrapping the dash in alcantra
RTFM!!!!!!!!!!! --> http://www.aeu86.org/technical/
- grappletech
- Club4AG Expert
- Posts: 344
- Joined: Sat Jan 12, 2013 12:13 pm
Re: Dash refurb: what fabric?
you could always take it to an upholstery shop. ask them how and what materials they would use...
87 GTS Coupe stock and Super Duper Clean
87 GTS Coupe Beams 3sge (under construction cuz I'm slow and lazy and broke-FML)
87 SR5 Coupe Shell. (Sold)
86 SR5 Hatch Shell
86 GT-SR5 Coupe 20v Swap
87 GTS Coupe Beams 3sge (under construction cuz I'm slow and lazy and broke-FML)
87 SR5 Coupe Shell. (Sold)
86 SR5 Hatch Shell
86 GT-SR5 Coupe 20v Swap
Re: Dash refurb: what fabric?
Great ideas guys. Flocking looks like it could be a big mess, and i'm not even sure I like the end result. Looking at the dash panel with the foam stripped off, it's actually really weird shaped above the gauge cluster. Wish I could post pics to show you guys. I am going to use a plastic tub cut up into strips to build it up and make it level again. Where the 3 Philips screws go in front of the gauge panel, there are 3 humps, then there are 2 deep grooves where the 2 bolts at the back go into the crash bar cover. It looks crazy all naked like this lol.
Eric'sFreeAE86 from the old site
Knockoff Crew member #0001
Knockoff Crew member #0001
Re: Dash refurb: what fabric?
Also, from what I've read about alcantara: expensive and might not stretch enough to fit smoothly around the contours of the dash. I reckon that's why flocking works on every surface cuz you spray it on.
Eric'sFreeAE86 from the old site
Knockoff Crew member #0001
Knockoff Crew member #0001
Re: Dash refurb: what fabric?
I busted up a plastic storage tub to make covers to fill in the vent and clock holes. As luck would have it, the depth of the lip on the dash is almost exactly double the thickness of the tub I cut up. So I made some shims for the covers and epoxy'd them all into place. I just need to fill in the small gaps around the edges and sand it smooth. It's not pretty, but I just need a smooth, flat surface to adhere the fabric to. I ordered some thin foam-backed suede today.
Eric'sFreeAE86 from the old site
Knockoff Crew member #0001
Knockoff Crew member #0001
-
- Club4AG Pro
- Posts: 582
- Joined: Wed Jan 09, 2013 6:10 pm
Re: Dash refurb: what fabric?
you could make a fiberglass mould at this point as well. DIY carbon dash.. the possibilities are endless.
RTFM!!!!!!!!!!! --> http://www.aeu86.org/technical/
Re: Dash refurb: what fabric?
I hadn't thought of that.... I reckon I could finish filling in the little gaps and I might be able to make a mould. Would anybody want a smoothed dash with no clock or vents? It would just be like a cap kinda.
Eric'sFreeAE86 from the old site
Knockoff Crew member #0001
Knockoff Crew member #0001
Re: Dash refurb: what fabric?
Received my material today. I need some super spray adhesive, and I need to finish smoothing out the edges on the dash. The material isn't as stretchy as I hoped, but the piece is about double the width I need, so I should be able to fit it smoothly without it ripping or bunching up. Lookin for free photo upload sites now...
Eric'sFreeAE86 from the old site
Knockoff Crew member #0001
Knockoff Crew member #0001
-
- Club4AG Pro
- Posts: 582
- Joined: Wed Jan 09, 2013 6:10 pm
Re: Dash refurb: what fabric?
imgur.com
its free, you dont have to make an acct either, if you dont wanna
its free, you dont have to make an acct either, if you dont wanna
RTFM!!!!!!!!!!! --> http://www.aeu86.org/technical/
-
- Club4AG Expert
- Posts: 273
- Joined: Sun Feb 17, 2013 6:58 pm
- Location: Kitanakagusuku, Okinawa
- Contact:
Re: Dash refurb: what fabric?
Flocked mine, simple to do, looks killer
-
- Club4AG Expert
- Posts: 273
- Joined: Sun Feb 17, 2013 6:58 pm
- Location: Kitanakagusuku, Okinawa
- Contact:
Re: Dash refurb: what fabric?
Also, the flocking filled in a couple of minor cracks I had. I made a FRP mold of a dash before, what a pain in the ass that was, hahaha
Re: Dash refurb: what fabric?
Flocking looks like a bit of a mess; at least I know it would be for me anyway lol. Hinga yours came out great! Until I started this project, I had no idea what that surface actually is. I always just thought it was alcantara or micro suede or some fancy material.
Eric'sFreeAE86 from the old site
Knockoff Crew member #0001
Knockoff Crew member #0001
-
- Club4AG Expert
- Posts: 273
- Joined: Sun Feb 17, 2013 6:58 pm
- Location: Kitanakagusuku, Okinawa
- Contact:
Re: Dash refurb: what fabric?
It's a little messy, but the flocking itself is easy to wash off the skin under running water with no scrubbing. As for it getting everywhere, I was wreckless with mine. They couldn't send the flocking adhesive to Japan, so I used black enamel paint, which dries quicker that I thought it would so I was shootin that mini-flocker like it was a mac-10. Got some paint on me, but only because I'm an impatient old bastard
For as quick as I did it, it turned out beautiful. I have that temp vent on the top of my dash and flocked right over it, haha.
For as quick as I did it, it turned out beautiful. I have that temp vent on the top of my dash and flocked right over it, haha.
-
- Club4AG Pro
- Posts: 582
- Joined: Wed Jan 09, 2013 6:10 pm
Re: Dash refurb: what fabric?
link me the kit, dude
RTFM!!!!!!!!!!! --> http://www.aeu86.org/technical/
Re: Dash refurb: what fabric?
This is what I have seen elsewhere....
http://www.donjer.com/
http://www.donjer.com/
Eric'sFreeAE86 from the old site
Knockoff Crew member #0001
Knockoff Crew member #0001
-
- Club4AG Expert
- Posts: 273
- Joined: Sun Feb 17, 2013 6:58 pm
- Location: Kitanakagusuku, Okinawa
- Contact:
Re: Dash refurb: what fabric?
http://www.flockit.com/index.php/order/ ... ibers.html
This is the kit I ordered. Better to have too much, than not enough.
This is the kit I ordered. Better to have too much, than not enough.
-
- Club4AG MASTER
- Posts: 2084
- Joined: Sun Jan 13, 2013 1:18 pm
- Contact:
Re: Dash refurb: what fabric?
Minky dot
https://www.fabric.com/apparel-fashion- ... tegoryLink
You will have the softest dash in the history of dashes.
https://www.fabric.com/apparel-fashion- ... tegoryLink
You will have the softest dash in the history of dashes.
-
- Club4AG Pro
- Posts: 582
- Joined: Wed Jan 09, 2013 6:10 pm
Re: Dash refurb: what fabric?
minky dot... only if its diamond pleated.. with buttons.
RTFM!!!!!!!!!!! --> http://www.aeu86.org/technical/
Re: Dash refurb: what fabric?
Lol some of those look like the color blind tests at the eye doctor lol. I gotta finish this thing up soon, some dude wants the car; but I've heard that a dozen times already and it's still here.....eating my money lol.
Eric'sFreeAE86 from the old site
Knockoff Crew member #0001
Knockoff Crew member #0001
-
- Club4AG Pro
- Posts: 582
- Joined: Wed Jan 09, 2013 6:10 pm
Re: Dash refurb: what fabric?
mmmm, delicious money. thats the elusive ae86's favorite food
RTFM!!!!!!!!!!! --> http://www.aeu86.org/technical/
-
- Club4AG Expert
- Posts: 418
- Joined: Wed Jan 09, 2013 9:16 pm
Re: Dash refurb: what fabric?
I have no idea on how the application works, but it seems there are many different ways to flock a surface? Did a quick search and it seems the applicator voltage and quality makes a big difference.
http://www.driftworks.com/forum/technic ... o-far.html
http://www.driftworks.com/forum/technic ... o-far.html
Silver/Black 1985 ae86 gts Heavens Gate Corolla
2001 Carbon Black e39 M5
89' Supra Twin Turbo 1JZ (sold)
2001 Carbon Black e39 M5
89' Supra Twin Turbo 1JZ (sold)
- RuizXIII
- Club4AG Enthusiast
- Posts: 165
- Joined: Wed Jan 16, 2013 7:33 pm
- Location: Smell Ya Later, NJ
Re: Dash refurb: what fabric?
Pics of your work would be sweet, Carbd7!
I think since most of our dashes are bunk/cracked, we should have an official dash refurbishment thread with various pics of different materials/methods/etc
Does anyone have what those 'dash cap' replacement covers look like installed?
The flocking looks pretty cool.
I was personally thinking about wrapping it in alacantara but I feel like it would be hard to execute an OEM type look
and when the material grain is not all going the same direction, it would drive me mad.
I think since most of our dashes are bunk/cracked, we should have an official dash refurbishment thread with various pics of different materials/methods/etc
Does anyone have what those 'dash cap' replacement covers look like installed?
The flocking looks pretty cool.
I was personally thinking about wrapping it in alacantara but I feel like it would be hard to execute an OEM type look
and when the material grain is not all going the same direction, it would drive me mad.
irony.cc
-
- Club4AG Expert
- Posts: 418
- Joined: Wed Jan 09, 2013 9:16 pm
Re: Dash refurb: what fabric?
Silver/Black 1985 ae86 gts Heavens Gate Corolla
2001 Carbon Black e39 M5
89' Supra Twin Turbo 1JZ (sold)
2001 Carbon Black e39 M5
89' Supra Twin Turbo 1JZ (sold)
- RuizXIII
- Club4AG Enthusiast
- Posts: 165
- Joined: Wed Jan 16, 2013 7:33 pm
- Location: Smell Ya Later, NJ
Re: Dash refurb: what fabric?
That looks very fresh, Chuck! Nice.
Did you simply place that atop the original cover or did you have to peel the old dash 'skin' off and glue that one in place?
How was fitment overall?
Did you simply place that atop the original cover or did you have to peel the old dash 'skin' off and glue that one in place?
How was fitment overall?
irony.cc